-
BLT hollow two-jaw long-stroke hydraulic chuck has the same size as BL hollow three-jaw long-stroke hydraulic chuck; BLT jaw has a larger stroke, 3 times that of the ordinary type.
-
There is a through hole in the center of the chuck, and the maximum stroke of the claw is large. The clamping range is large. It is suitable for clamping rod-type workpieces. The stroke of the BL claw is large, which is 3 times...
-
The center through hole is relatively large. Suitable for clamping rod-type workpieces.
-
It is a center through hole chuck suitable for processing square and special-shaped long strip parts, and can replace the hard jaws.
-
It is a center through hole chuck suitable for processing square and special-shaped long strip parts, and can replace the hard jaws.
-
It is a center through-hole chuck suitable for clamping rod-type workpieces; Repeat positioning accuracy can reach: 0.02mm.
-
The MEA/B spreader mechanism is fed by rack and gear or single inclined wedge transmission,The feed speed is stable; The feed speed and stroke are very easy to adjust; The chuck body is surface hardened and ground, and the rigidity and durability are very...
-
MPS diaphragm chuck is a fully sealed chuck with 3-claw and 6-claw options; It is clamped based on the outer diameter P.C.D of the gear, and can process the inner diameter and end face of the gear to achieve better concentricity requirements; When processing...
-
MPS diaphragm chuck is a fully sealed chuck with 3-claw and 6-claw options; It is clamped based on the outer diameter P.C.D of the gear, and can process the inner diameter and end face of the gear to achieve better concentricity requirements; When processing...
-
Kf chuck is also a special chuck for shaft processing. It takes the axis as the reference, and the jaws have compensation function. It is used when concentricity is important. The compensation amount for the center jaw is 5-10MM. Because the center uses an...
-
The shaft processing chuck is available with a fixed center or an elastic center. Features of the end face drive chuck with a fixed center (equipped with a double piston cylinder):① Positioning with an axial center hole;② The fixed center can ensure the concentricity...
-
BF chuck is a back-pull flat clamping, which can be adjusted according to the thickness of the workpiece. Suitable for thin-walled workpieces that cannot be clamped due to inner and outer diameters.
-
BF chuck is a back-pull flat clamping, which can be adjusted according to the thickness of the workpiece. Suitable for thin-walled workpieces that cannot be clamped due to inner and outer diameters.
-
The inclined column back-pull chuck is available in two-jaw, three-jaw, two-jaw and three-jaw hollow types. The inclined column back-pull chuck is suitable for workpieces with requirements for end face positioning, verticality and parallelism; when loading different workpieces, you only need to replace the clamping...
-
The inclined column back-pull chuck is available in two-jaw, three-jaw, two-jaw and three-jaw hollow types. The inclined column back-pull chuck is suitable for workpieces with requirements for end face positioning, verticality and parallelism; when loading different workpieces, you only need to replace the clamping...
-
Pull the workpiece towards the baffle and clamp it at the same time, so it has the function of completely sticking the workpiece to the reference surface. It is particularly suitable for workpieces that require high verticality and concentricity processing accuracy of the reference...
-
The inclined column back-pull chuck is available in two solid jaws, three jaws and two hollow jaws, three jaws. The inclined column back-pull chuck is suitable for processing workpieces with requirements for end face positioning, verticality and parallelism; when loading different workpieces, you only...
-
The inclined column back-pull chuck is available in two solid jaws, three jaws and two hollow jaws, three jaws. The inclined column back-pull chuck is suitable for processing workpieces with requirements for end face positioning, verticality and parallelism; when loading different workpieces, you only...
-
This chuck has the characteristics of pulling the inner diameter of the workpiece and clamping it. It is used when verticality and parallelism are important, and the clamping range is large. Only the top soft claws can be replaced to process a variety of...
-
The BU back-pull three-jaw chuck has the same size as the BUT back-pull two-jaw chuck. The BU back-pull chuck is suitable for processing workpieces with requirements for verticality and parallelism. This type of chuck has a wide clamping range. When loading different workpieces, you...
-
The BU back-pull three-jaw chuck has the same size as the BUT back-pull two-jaw chuck. The BU back-pull chuck is suitable for processing workpieces with requirements for verticality and parallelism. This type of chuck has a wide clamping range. When loading different workpieces, you...
-
Anti-iron chips and coolant, making the internal mechanism free from pollution. The surface of the chuck body and internal parts are quenched and long-term lubrication is used to ensure high precision and long service life. Centrifugal force compensation. Suitable for high-low pressure clamping.
-
Anti-iron chips and coolant, making the internal mechanism free from pollution. The surface of the chuck body and internal parts are quenched and long-term lubrication is used to ensure high precision and long service life. Centrifugal force compensation. Suitable for high-low pressure clamping.
-
Vendor: 9stellarSWT Self-Centering Compensation Pull Back 2 Jaw Chuck
● DeliverableInquiry3 variants -
Vendor: 9stellarSW Self-Centering Compensation Pull Back 3 Jaw Chuck
● DeliverableInquiry8 variantsAnti-iron chips and coolant, making the internal mechanism free from pollution. The surface of the chuck body and internal parts are quenched and long-term lubrication is used to ensure high precision and long service life. Centrifugal force compensation. Suitable for high-low pressure clamping.
-
The chuck has a through hole in the center, and its performance is similar to that of the KW chuck.
-
The connection method of KWT strong floating chuck is the same as that of KW.
-
Strong floating 2-jaw and 3-jaw chucks are very suitable for casting and forging automatic centering or automatic compensation turning processes. Their functions and features are: The workpiece is clamped and pulled back, and can clamp a 10° dimension. The jaws are free to swing...
-
NHRF chuck has dual sensing signal device. NHRF chuck can be divided into 8x45° 4x90°. NHRF chuck can replace the jaws and the connection method is as convenient as NHR.
-
NHRL chuck can be indexed 2×180°. After the part is clamped once, two surfaces can be processed. NHRL chuck can be easily replaced and connected as NHR.
Collections
Nuestros mejores vendedores
Vendor:
9stellar
KB-A Adaptor Plates
Figure 1 is for direct mounting - when the spindle size and chuck diameter are standard; Figures 2 and 3 are for indirect mounting (reduction and increase) - when the spindle size and chuck diameter are not standard.
Inquiry
This is a high-speed through-hole rotary cylinder equipped with a high-speed diagnostic valve to prevent a sudden drop in pressure during a power outage; Lightweight and capable of high-speed rotation; Large through-hole, capable of using a wider range of rods; A variety of rotary...
Inquiry
This is a high-speed through-hole rotary cylinder equipped with a high-speed diagnostic valve to prevent a sudden drop in pressure during a power outage;it is light in weight and can rotate at high speed; the through-hole is large, allowing a wider range of rods...
Inquiry
This is a commonly used rotary cylinder, which is light in weight and small in size, and can be installed in many devices in horizontal or vertical directions.
Inquiry
A solid hydraulic rotary cylinder that can determine the position.It is equipped with a high-speed diagnostic valve to prevent sudden pressure drop during power failure. Many devices can be installed in both horizontal and vertical directions.
Inquiry
The most commonly used rotary cylinder, it is equipped with a high-speed diagnostic valve to prevent a sudden drop in pressure during a power outage, and many devices can be installed in both horizontal and vertical directions.
Inquiry
The aluminum alloy exterior structure is lighter and smaller than traditional rotary cylinders.It can maintain stable performance and reduce the mechanical burden during high-speed rotation.
Inquiry
LUE built-in internal support gas and hydraulic chucks are assembled with PUE internal support chucks and LY vertical cylinders; Chucks fixed on drilling machines, milling machines or machining centers are easy to use, exquisitely designed, and simple to install; LUE built-in oblique column gas...
Inquiry
The inclined column design provides high precision and strong clamping force during processing;
Suitable for fixed pneumatic chucks such as drilling machines, milling machines, tapping machines and machining centers;
Can use air pressure or oil pressure.
Inquiry
Vendor:
9stellar
LY Vertical Cylinder
Easy to install on fixed cylinders such as drilling machines, milling machines, tapping machines and machining centers.
Can be operated by air pressure or oil pressure.
Inquiry
There is a through hole in the center of the chuck; It is suitable for fixed pneumatic chucks such as drilling machines, milling machines, tapping machines and machining centers. Multiple chucks can be assembled on the platform to save downtime; It can use air...
Inquiry
- Choosing a selection results in a full page refresh.