![[CK AUTO TAPPER E] M3 - M24 Combination With A Long Type CK Shank is Convenient When Long Tapper Is Required](http://big-tools.com/cdn/shop/files/CKAUTOTAPPERE_M3-M24CombinationwithalongtypeCKShankisconvenientwhenlongtapperisrequired-1_785x.jpg?v=1719199920)
![[CK AUTO TAPPER E] M3 - M24 Combination With A Long Type CK Shank is Convenient When Long Tapper Is Required](http://big-tools.com/cdn/shop/files/CKAUTOTAPPERE_M3-M24CombinationwithalongtypeCKShankisconvenientwhenlongtapperisrequired-2_785x.jpg?v=1719199920)
-
There is a through hole in the center of the chuck, and the maximum stroke of the claw is large. The clamping range is large. It is suitable for clamping rod-type workpieces. The stroke of the BL claw is large, which is 3 times...
-
-
The center through hole is relatively large. Suitable for clamping rod-type workpieces.
-
It is a center through hole chuck suitable for processing square and special-shaped long strip parts, and can replace the hard jaws.
-
-
It is a center through hole chuck suitable for processing square and special-shaped long strip parts, and can replace the hard jaws.
-
-
Vendor: 9stellarBT-Extended Series Tension and Compression Taper Holder
● DeliverableInquiry7 variants -
It is a center through-hole chuck suitable for clamping rod-type workpieces; Repeat positioning accuracy can reach: 0.02mm.
-
Vendor: 9stellarMTA-GTP High Precise Torsion Tension and Compression Tapping Holder
● DeliverableInquiry5 variants
-
The MEA/B spreader mechanism is fed by rack and gear or single inclined wedge transmission,The feed speed is stable; The feed speed and stroke are very easy to adjust; The chuck body is surface hardened and ground, and the rigidity and durability are very...
-
MPS diaphragm chuck is a fully sealed chuck with 3-claw and 6-claw options; It is clamped based on the outer diameter P.C.D of the gear, and can process the inner diameter and end face of the gear to achieve better concentricity requirements; When processing...
-
Vendor: 9stellarStraight Shank-GTP High Precise Torsion Tension and Compression Tapping Holder
● DeliverableInquiry6 variants
-
Vendor: 9stellarCAT-GTP High Precise Torsion Tension and Compression Tapping Holder
● DeliverableInquiry6 variants
-
MPS diaphragm chuck is a fully sealed chuck with 3-claw and 6-claw options; It is clamped based on the outer diameter P.C.D of the gear, and can process the inner diameter and end face of the gear to achieve better concentricity requirements; When processing...
-
Vendor: 9stellarHSK-GTP High Precise Torsion Tension and Compression Tapping Holder
● DeliverableInquiry5 variants
-
Vendor: 9stellarJP-GTP High Precise Torsion Tension and Compression Tapping Holder
● DeliverableInquiry6 variants
-
Kf chuck is also a special chuck for shaft processing. It takes the axis as the reference, and the jaws have compensation function. It is used when concentricity is important. The compensation amount for the center jaw is 5-10MM. Because the center uses an...
-
Vendor: 9stellarBT-GTP High Precise Torsion Tension and Compression Tapping Holder
● DeliverableInquiry6 variants
-
The shaft processing chuck is available with a fixed center or an elastic center. Features of the end face drive chuck with a fixed center (equipped with a double piston cylinder):① Positioning with an axial center hole;② The fixed center can ensure the concentricity...
-
-
BF chuck is a back-pull flat clamping, which can be adjusted according to the thickness of the workpiece. Suitable for thin-walled workpieces that cannot be clamped due to inner and outer diameters.
-
BF chuck is a back-pull flat clamping, which can be adjusted according to the thickness of the workpiece. Suitable for thin-walled workpieces that cannot be clamped due to inner and outer diameters.
-
-
-
-
-
-
The inclined column back-pull chuck is available in two-jaw, three-jaw, two-jaw and three-jaw hollow types. The inclined column back-pull chuck is suitable for workpieces with requirements for end face positioning, verticality and parallelism; when loading different workpieces, you only need to replace the clamping...
-
Collections
Our Top Sellers
- From $202.00
- From $202.00
- Unit price
- per
- From $507.00
- From $507.00
- Unit price
- per
New Products
The most commonly used rotary cylinder, it is equipped with a high-speed diagnostic valve to prevent a sudden drop in pressure during a power outage, and many devices can be installed in both horizontal and vertical directions.
Inquiry
The aluminum alloy exterior structure is lighter and smaller than traditional rotary cylinders.It can maintain stable performance and reduce the mechanical burden during high-speed rotation.
Inquiry
LUE built-in internal support gas and hydraulic chucks are assembled with PUE internal support chucks and LY vertical cylinders; Chucks fixed on drilling machines, milling machines or machining centers are easy to use, exquisitely designed, and simple to install; LUE built-in oblique column gas...
Inquiry
The inclined column design provides high precision and strong clamping force during processing;
Suitable for fixed pneumatic chucks such as drilling machines, milling machines, tapping machines and machining centers;
Can use air pressure or oil pressure.
Inquiry
Vendor:
9stellar
LY Vertical Cylinder
Easy to install on fixed cylinders such as drilling machines, milling machines, tapping machines and machining centers.
Can be operated by air pressure or oil pressure.
Inquiry
There is a through hole in the center of the chuck; It is suitable for fixed pneumatic chucks such as drilling machines, milling machines, tapping machines and machining centers. Multiple chucks can be assembled on the platform to save downtime; It can use air...
Inquiry
Suitable for processing square and special-shaped objects.
Fixed pneumatic chuck for drilling machines, lathes, tapping machines, machining centers, etc.:
Easy to use because it uses pneumatic pressure. Small design and easy installation.
Inquiry
Fixed pneumatic chuck for drilling machines, lathes, tapping machines, machining centers, etc.:
Easy to use because it uses pneumatic pressure. Small design and easy installation.
Inquiry
Used for processing square or special-shaped workpieces;
Strong clamping force, capable of strong chip cutting;
Use connecting plate for connection.
Inquiry
It is a crank type chuck;
It has strong clamping force and can do strong cutting;
If you need to customize a chuck with different specifications and large stroke, please contact us.
Inquiry
It is a crank type chuck;
It has strong clamping force and can do strong cutting;
If you need to customize a chuck with different specifications and large stroke, please contact us.
Inquiry
The clamping force is large, and the medium and large stroke has a large clamping range. It is suitable for processing a certain workpiece and is relatively economical; When processing different workpieces, you only need to replace the clamps to use it; Repeat positioning...
Inquiry
- Choosing a selection results in a full page refresh.